FACK
Liên hệ
Flexible Coupling – Jaw coupling with urethane spider – Clamping screw with key way Operating temperature: -20o C~60o C. Offset, deflection, shaft deviation are individual allowed values, so axial offsets in all reasons appearing at same time would reduce values.
| Component | Material | Surface finish | Accessories |
| Main frame | Aluminum Alloy | Anodized | Clamp screw |
| Spider | Urethane(PU) | – |
★ Dimension “C”, must be previously kept while assembly by users, otherwise it would affect allowed deflection, accelerating shaft and coupling damage.
| Dimensions | Insert ring | Ød1&Ød2 selection *Ød1≦ Ød2 | Allowable wrench torque (N．m) | ||||||||
| Model no. | ØD | (color selection) | 10 | 11 | 12 | 14 | 15 | 16 | B | W | R |
| FACK | 30 | B(Blue)W(White)R(Red) | ‧ | ‧ | ‧ | 4 | 7.5 | 12.5 | |||
| FACK | 40 | B(Blue)W(White)R(Red) | ‧ | ‧ | ‧ | ‧ | ‧ | ‧ | 4.9 | 10 | 17 |
| Introduction |
| ♦ Coupling is a mechanism device, connecting transmission between two shafts and transmitting safety torque.
♦ Coupling divided into “Flexible type” and “Rigidity type”. ♦ To apply flexible couplings timing in case of power transmission, two shafts are not easy to set in alignment, or to simplify two shafts installation. It contains shock buffer to absorb parallelism, deflection, axial displacement, deviation improvement, and improvement of traditional transmission power, so few deviation would not cause any unusual situation on bearing. It is widely applied to current markets. ♦ Rigidity coupling is a unit causing non-eccentric, non-deflection, and make two connected shafts fixed in one unit. Users must do the best to have motor running and axis of load in alignment due to high requirement of concentricity, also means of axis has to be calibrated strictly; otherwise, the rotating shaft would be broken caused by mechanism fatigue, also the bearing would be thermal abrasion due to eccentric load, those were brought by continuous vibration of the axis during long term running of the motor. The advantage of rigidity couplings is to transmit transmission torque precisely. |
Fixing Type |
| ♦ Fixing (1) There are five ways to fix coupling onto shaft as below. Please select coupling as your demand. (2) Set screw or clamping screw (hexagonal countersink screw) shall be secured by screwdriver or torque wrench. Securing torque refer to product specification.♦ Set screw fixing： This fixing in low cost is the most traditional. Front of screw contacting with axis directly may cause damage or difficult disassembly. ♦ Clamping fixing： ♦ Separation fixing： ♦ Key way fixing： ♦ Zero Backlash type： |
Motor Reference |
| ♦ Induction motor (1) More than triple torque occurs in case of running momently. (2) Shaft axis center of the motor has ±1.5mm movement back and forth while running, and it’s not recommended to use spiral beam type. (3) DC motor could be used in working environment with dust.♦ Stepping motor (1) Without triple torque in case of running momently, but max. rated torque of motor occurs. (2) Larger torque in low speed than servo motor in same level. (3) Higher RPM, smaller torque in motor. (4) Motor have temperature rise in case of running continuously.( to improve by using disk type coupling) * Force output in stepping motor is smaller than servo motor. ♦ Servo motor ♦ Encoder |
Be the first to review “FACK”
Related products
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Reviews
There are no reviews yet.