CYC80 – Standard
Liên hệ
★ Guide- Circular linear ball guiding, Gothic arc-groove formed by dual arc-grooves individually on upper and lower rails of body. Ball moving in single groove is structured by 2 points-contact, and total 4contact points in dual arc-groove to form strong rail constructure.
★ Transmission Parts-Ball screw, It transmits through the ball involving in the locknut and screw to reach the accuracy and longer operation lifetime.
★ Material-Stainless Steel, Carbon Steel
★This product pic. shows as CYC6075-S2NN-ND which is only for reference, please base on below specification for further information.
|
Model No. |
CYC8030-S2NN-ND-P1 CYC8030-F2NN-ND-P1 |
CYC8030-S2NN-ND-P2 CYC8030-F2NN-ND-P2 |
CYC8050-S2NN-ND-P1 CYC8050-F2NN-ND-P1 |
CYC8050-S2NN-ND-P2 CYC8050-F2NN-ND-P2 |
CYC8075-S2NN-ND-P1 CYC8075-F2NN-ND-P1 |
CYC8075-S2NN-ND-P2 CYC8075-F2NN-ND-P2 |
||
|
Mechanical Spec. |
Table Size (mm) |
80 X 80 | ||||||
|
Travel Stroke (mm) |
30 | 50 | 75 | |||||
|
Drive Type |
Ball screw Ø8
lead 1 mm |
Ball screw Ø8
lead 2 mm |
Ball screw Ø8
lead 1 mm |
Ball screw Ø8
lead 2 mm |
Ball screw Ø8
lead 1 mm |
Ball screw Ø8
lead 2 mm |
||
|
Rail |
Circular Linear Ball Guiding | |||||||
|
Stage Material / Surface Treatment |
S：Stainless Steel / Nickel Plating
F：Carbon Steel / Nickel Plating |
|||||||
|
Main Unit Weight (Kg) |
3.58 | 3.72 | 4.06 | |||||
|
Coupling |
FAMCS11.6-5*5 | |||||||
|
Accuracy Level |
N：Standard grade | |||||||
|
Wiring Method |
N：GMT Standard | |||||||
|
Precision Spec. |
Resolution (Pulse) (µm) |
5 (Full)
2.5 (Half) |
10 (Full)
5 (Half) |
5 (Full)
2.5 (Half) |
10 (Full)
5 (Half) |
5 (Full)
2.5 (Half) |
10 (Full)
5 (Half) |
|
|
Max. Speed (Full Step) (mm / sec) |
20 | 40 | 20 | 40 | 20 | 40 | ||
|
Positioning Presion (µm) |
15 | |||||||
|
Repeatability Precision (µm) |
± 1 | |||||||
|
Load Capacity (Kgf) |
14 | |||||||
|
Missed Step (µm) |
3 | |||||||
|
Parallelism (µm) |
20 | |||||||
|
Dynamic Straightness (µm) |
3 | |||||||
|
Dynamic Parallelism (µm) |
10 | |||||||
|
Electrical Spec. |
Motor |
Type / Shaft Numbers |
2-phase stepper / ☐ 28 double shafts | |||||
|
Brand / Model |
GMT / 2MS-N28D32A | |||||||
|
Driver Brand / Model |
GMT / GTR22G-D (Additional options) | |||||||
|
Connector |
Stage Side Connector |
15-Pin male end connetor D-SUB / 12-Pin male end connetor HRS | ||||||
|
Controller Side Connector |
15-Pin female end connetor D-SUB / 12-Pin female end connetor HRS (Additional options) | |||||||
|
Sensor |
Origin Sensor |
Photoelectric sensor GMT-sensor | ||||||
|
Limit Sensor |
||||||||
|
Origin Approximation Sensor |
N / A | |||||||
|
Power Voltage |
24V ± 10% | |||||||
|
Control Output |
NPN open collector output under 24V 8mA | |||||||
|
Output Control |
Testing (sensing)：output transistor OFF (closed) | |||||||
| System Configuration Diagram |
| ♦ For selection of the drivers preferred, please refer to the reference table or the catalogue of Motor・Driver.
♦ All of the drivers chosed are the specification of GMT preferred. For different needs, please choose the suitable drivers according to real functional needs.
|
| Axis Definition |
| GMT has defined different axis as the following figuration according to the movement direction:
Horizontal movement direction is X and Y axis. Vertical movement direction is Z axis. Movement around X, Y, Z axis is defined to α axis, β axis, and θ axis. Green arrows present the specified axis movement direction.
|
Motor・driver Reference Table |
 |
|
|
Be the first to review “CYC80 – Standard”
Related products
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Reviews
There are no reviews yet.