AR80 – Standard
Liên hệ
★ Guide-Deep Groove Ball Bearing, It enables the bearings to accommodate radial and axial loads in both directions to reach high precision and high speed- revolving.
★ Transmission parts-Worm & Worm Gear, It transmits through the gear and is usually used in Reducer.
★ Material-Aluminum Alloy
★This product pic. shows as AR59-A3NN-ND.
|
Model No. |
AR80-A3NN-ND |
|||
|
Mechanical Spec. |
Table Size (mm) |
Ø 80 | ||
|
Travel Stroke (°) |
360 | |||
|
Drive Type |
Worm & Worm gear (Ratio 1 / 180) | |||
|
Rail |
Deep Groove Ball Bearing | |||
|
Stage Material / Surface Treatment |
Aluminum Alloy / Black anodized | |||
|
Main Unit Weight (Kg) |
0.8 | |||
|
Coupling |
FAMMS12-5*5 | |||
|
Accuracy Level |
N：Standard grade | |||
|
Wiring Method |
N：GMT Standard | |||
|
Precision Spec. |
Resolution (Pulse) (°) |
0.01 (Full) | 0.005 (Half) | |
|
Max. Speed (Full Step) ( ° / sec) |
15 | |||
|
Positioning Presion (°) |
0.1 | |||
|
Repeatability Precision (°) |
± 0.05 | |||
|
Load Capacity (Kgf) |
4 | |||
|
Missed Step (°) |
0.1 | |||
|
Parallelism (µm) |
50 | |||
|
Dynamic Straightness (µm) |
30 | |||
|
Dynamic Parallelism (µm) |
30 | |||
|
Electrical Spec. |
Motor |
Type / Shaft Numbers |
2-phase stepper / ☐ 28 double shafts | |
|
Brand / Model |
GMT / 2MS-N28D45A | |||
|
Driver Brand / Model |
GMT / GTR22G-D (Additional options) | |||
|
Connector |
Stage Side Connector |
15-Pin male end connetor D-SUB / 12-Pin male end connetor HRS | ||
|
Controller Side Connector |
15-Pin female end connetor D-SUB / 12-Pin female end connetor HRS (Additional options) | |||
|
Sensor |
Origin Sensor |
Photoelectric sensor GMT-sensor | ||
|
Limit Sensor |
||||
|
Power Voltage |
24V ± 10% | |||
|
Control Output |
NPN open collector output under 24V 8mA | |||
|
Output Control |
Testing (sensing)：output transistor OFF (closed) | |||
| System Configuration Diagram |
| ♦ For selection of the drivers preferred, please refer to the reference table or the catalogue of Motor・Driver.
♦ All of the drivers chosed are the specification of GMT preferred. For different needs, please choose the suitable drivers according to real functional needs.
|
| Axis Definition |
| GMT has defined different axis as the following figuration according to the movement direction:
Horizontal movement direction is X and Y axis. Vertical movement direction is Z axis. Movement around X, Y, Z axis is defined to α axis, β axis, and θ axis. Green arrows present the specified axis movement direction.
|
Motor・driver Reference Table |
 |
|
|
Hãy là người đầu tiên nhận xét “AR80 – Standard”
Sản phẩm tương tự
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Đánh giá
Chưa có đánh giá nào.