Model No. |
CXS50 |
|||
Mechanical Spec. |
Table Size (mm) |
50X50 | ||
Travel Stroke (mm) |
20、30 | |||
Drive Type |
Ball Screw Ø8,lead 1mm | |||
Rail |
Linear Ball Guiding | |||
Stage Material / Surface Treatment |
Stainless Steel / Nickel plating | |||
Accuracy Level |
OP:Ultra Precision | |||
Wiring Method |
N:GMT Standard | |||
Precision Spec. |
Resolution(Pulse) (µm) |
M: 1 (Full);0.5 (Half)
J: 2 (Full);1 (Half) |
||
Max. Speed(Full Step) (mm/sec) |
15 | |||
Positioning Precision (µm) |
5 | |||
Repeatability Precision(µm) |
±0.5 | |||
Multi-point Repeatability Precision(µm) |
A: 1.5 / B: 1 | |||
Load Capacity (Kgf) |
6 | |||
Missed Step (µm) |
1 | |||
Moment Stiffness |
Pitch: 0.11 / Yaw: 0.09 / Rolling: 0.09 (“/N-cm) | |||
Pitch / Yaw |
Pitch: < 20″ / Yaw: < 15″ | |||
Parallelism (µm) |
15 | |||
Dynamic Straightness (µm) |
2 | |||
Dynamic Parallelism (µm) |
10 | |||
Electrical Spec. |
Motor |
Type / Shaft Numbers |
M: 5-phase stepper high-resolution motor / ☐28 double shafts
J: 5-phase stepper motor / ☐28 double shafts |
|
Brand / Model |
M: Orientalmotor / PK523HPMB
J: Orientalmotor / PKP523N12B |
|||
Driver Brand / Model |
Orientalmotor / CVD Series – 5 Phase stepping motor (Additional options) | |||
Connector |
Stage Side Connector |
15-Pin male end connetor D-SUB / 12-Pin male end connetor HRS | ||
Controller Side Connector |
15-Pin female end connetor D-SUB (Additional options) / 12-Pin female end connetor HRS (Additional options) | |||
Sensor |
Origin Sensor |
Photoelectric sensor GMT-sensor | ||
Limit Sensor |
||||
Origin Approximation Sensor |
N / A | |||
Power Voltage |
24V±10% | |||
Control Output |
NPN open collector output under 24V 8mA | |||
Output Control |
Testing (sensing):output transistor OFF (closed) |
Multi-point repeated positioning accuracy |
♦ Accuracy measurement description
1. Unidirectional positioning accuracy: within the range of the predetermined detection stroke, starting from a starting position, moving and positioning in a certain direction sequentially, and detecting the actual ♦ Precision introduction 1. Design the GMT high-level precision inspection method to meet the precision requirements of fiber coupling and semiconductor manufacturing process. |
System Configuration Diagram |
♦ For detailed specifications, please read the description for the stage and connecting cable.
♦ For selection of driver, please refer to the cross-reference table for the motor/driver of the standard motorized stage or the GMT motor and driver catalog. ♦ The most preferred driver is recommended to be specified by GMT as considerations. For different needs, please choose the suitable driver based on real functional needs. |
Axis Definition |
GMT has defined different axis as the following figuration according to the movement direction:
Horizontal movement direction is X and Y axis. Vertical movement direction is Z axis. Movement around X, Y, Z axis is defined to α axis, β axis, and θ axis. Green arrows present the specified axis movement direction. |
Motor/driver |
Đánh giá
Chưa có đánh giá nào.